Aluminum Backup Pads for Sanding Disks

Photo: Aluminum Sanding Backup Pads (aluminum_bu_pads_00)

Aluminum Sanding Backup Pads are the Rolls-Royce of Backup Pads. They are not necessary. You can make your own or use cheap plastic ones.

However, good plastic ones may cost almost as much. I have found that the extra weight of an Aluminum Backup Pad acts sort of like a fly wheel that makes things run smoother. They are heavy, but not top heavy. I like them.

I really like them for 5" sanding disks.

Note: I like Sanding Backup Pads (mandrels) that are thin, low profile and HARD. I add (attach) firm or soft foam interface pads to make them softer as needed. See my Carl’s Sanding Backup Pads blog entry for more information.

Photo: 3 Inch Aluminum Backup Pad (amazon_3i_aluminum_backup)
3 Inch Aluminum Backup Pad

I purchased my ComeFloor (brand) 3 inch Aluminum Backup Pad from Amazon. $12 on 10/2025.

Google Amazon ComeFloor 3 Inch Aluminum Backer Pad Hook And Loop google!

Photo: 3 Inch Aluminum Backup Pad (1) Note: You can also purchase 4", 5", 6" and 7" Aluminum Backer Pads. I can't find a source for Aluminum 2" pads.

Photo: 5 Inch Aluminum Backup Pad (amazon_5i_aluminum_backup)
5 Inch Aluminum Backup Pad

I purchased my ComeFloor (brand) 5 inch Aluminum Backup Pad from Amazon. $17 on 10/2025.

Google Amazon ComeFloor 5 Inch Aluminum Backer Pad Hook And Loop google!

Photo: 3/8
3/8″ Mandrel Drill Adapter

You need a 3/8" Mandrell Drill Adapter to use the above Aluminum Backup Pads in a run of the mill drill with a 3/8" or bigger chuck. 2 for $9 on 10/2025.

I RECOMMEND a mandrel with a 3/8" or 8mm shaft, rather than one with a 1/4" shaft. A 1/4" shaft is not adequate for a 5" Aluminum Backup Pad. I bent a 1/4" shaft mandrel.

I permanently 5 Minute Epoxy the mandrel in place. This allows me to run the drill in forward or reverse.

Google Amazon JUNLIXN 5/8”-11 UNC Thread To 8mm Shank For Use With Drills google!

Note: You should sand with a drill rather than an angle grinder. You can thread the above disks with a 5/8″-11 thread directly onto an angle grinder. However, variable speed angle grinders typically run from 2800 RPM to 11000 RPM. To fast for sanding! Angle drills for sanding typically top out at 1400 RPM (0 to 1400 RPM).

6″ Backup Pad?

Photo: 6

I have a 6" Aluminum Backup Pad. Why? Mirka Autonet (aka Abranet) only comes in 3" and 6" disks. No 5" disks. I like to use Autonet for sanding wet wood. Thus I have 6" Autonet set of interface and sanding disks.

Photo: 6 See my Mirka Autonet Sandpaper blog entry for more information.

DIY Backup Pads

Photo: DIY Backup Pads (sanding_backup_pads_blue)

I started making my own Sanding Backup Pads a couple of years ago when the price on commercially available ones went to $12. Way to much!

I make my backup pads out of 1/4" plywood and 1/4" flat head bolts.

I recommend using a 3/8″ (rather than a 1/4″) Flat Head Bolt for 5 inch or larger DIY pads. A 1/4″ blot bends to easily. A 5 inch disk creates to much leverage.

See my Carl’s Sanding Backup Pads blog entry for more information.

5 Inch Sanding Disks

5 Inch Sanding Disks

You should also check out my 5 Inch Sanding Disks blog entry.